NOMINAL OPERATING LEVEL
(Peak Ceiling RANGE switch) INPUT
Connector: 3-Pin XLR female (pin 1 ground, pin 2 positive, pin 3 negative)
Type Transformerless, servo balanced with passive 4th order RF filter Chassis grounded per AES standards
Impedance:
19.5 kΩ Unterminated;
600Ω with rear-panel terminator engaged (terminator lifts in bypass)
Nominal level:
0dBu (for use with +4 or +8dBu)
from 0dBu to +8dBu
-10dBu
-from -10dBu to 0dBu
Maximal level:
0dBu (for use with +4 or +8dBu)
+26dBu
-10dBu
+16dBu (+14.8dBV)
CMRR:
> 50dB 20Hz to 10kHz
RF Rejection:
> 28dB at 800 kHz; > 60dB above 2 mHz
OUTPUT
Connector:
3-Pin XLR male (pin 1 ground, pin 2 positive, pin 3 negative)
Type:
Transformerless, servo balanced, chassis grounded per AES standards
Output Impedance:
65Ω
Nominal Level:
0dBu (for use with +4 or +8dBu)
from 0dBu to +8dBu
-10dBu
from -10dBu to 0dBu
Maximum Level:
0dBu (for use with +4 or +8dBu)
+25dBu peak value of sine wave
-10dBu
+15dBu PK*
AUDIO (Controls set for unity gain, no limiting and flat response except as otherwise noted)
Dynamic Range:
0dBu (for use with +4 or +8dBu)
> 108dB
-10dBu
>106dB
Hum & Noise (unweighted, 22 Hz - 22 kHz):
0dBu (for use with +4 or +8dBu)
< -82dBu
-10dBu
< -90dBu
Crosstalk:
< -60dB up to 10kHz
THD (Ref.: 1kHz, no limiting):
0dBu (for use with +4 or +8dBu)
< 0.006% (+12dBu in)
-10dBu
< 0.006% (+2dBu in)
SMPTE IMD:
0dBu (for use with +4 or +8dBu)
< 0.006% (+12dBu in)
-10dBu
< 0.006% (+2dBu in)
INPUT GAIN:
+14/-21 dB typical
720 CONTROL & METERING PARAMETERS (on front panel unless otherwise noted)
PROCESS ON/OFF:
ON: Active / OFF: Hardwire Bypass
LF EQ Boost/Cut:
± 5 dB
HF EQ Boost/Cut:
± 5 dB
XOVER 1 Frequency:
100 Hz / 210 Hz
XOVER 2 Frequency:
1.7 kHz / 3.4 kHz
RELEASE Time:
150 mSec to 7 Sec
RCH (Relative Crest Height) DENSITY: STEREO COUPLING:
-5 to +5
STEREO COUPLING:
ON/OFF
PEAK CEILING:
0dBu (for use with +4 or +8dBu)
+1 to +25dBu (PK)**
Peak Ceiling is adjusted with the COARSE (2dB steps), FINE (0.2dB steps) and RANGE (0dB/-10dB) controls
-10dBu
-9 to +15dBu (PK)
LIMITING Meter:
10 segment meter indicates up to 15dB of gain reduction in the channel with the greatest amount of limiting.
600 OHM INPUT TERMINATION:
Each channel is switchable on rear panel (lifts in bypass)
REMOTE Control Jack:
A four pin RJ11 telephone-style connector on the rear panel provides remote control capacity of the PROCESS ON/OFF bypass relays and dry “tally” contact for a remote status indicator
722 CONTROL PARAMETERS
NOMINAL OPERATING LEVEL
(Peak Ceiling RANGE switch) INPUT
Connector: 3-Pin XLR female (pin 1 ground, pin 2 positive, pin 3 negative)
Type Transformerless, servo balanced with passive 4th order RF filter Chassis grounded per AES standards
Impedance:
19.5 kΩ Unterminated;
600Ω with rear-panel terminator engaged (terminator lifts in bypass)
Nominal level:
from 0dBu to +8dBu
Maximal level:
+26dBu
CMRR:
> 50dB 20Hz to 10kHz
RF Rejection:
> 28dB at 800 kHz; > 60dB above 2 mHz
OUTPUT
Connector:
3-Pin XLR male (pin 1 ground, pin 2 positive, pin 3 negative)
Type:
Transformerless, servo balanced, chassis grounded per AES standards
Output Impedance:
65Ω
Nominal Level:
from 0dBu to +8dBu
Maximum Level:
+25dBu peak value of sine wave
AUDIO (Controls set for unity gain, no limiting and flat response except as otherwise noted)
Dynamic Range:
> 108dB
Hum & Noise (unweighted, 22 Hz - 22 kHz):
< -82dBu
Crosstalk:
< -60dB up to 10kHz
THD (Ref.: 1kHz, no limiting):
< 0.006% (+12dBu in)
SMPTE IMD:
< 0.006% (+12dBu in)
INPUT GAIN:
+14/-21 dB typical
720 CONTROL & METERING PARAMETERS (on front panel unless otherwise noted)
PROCESS ON/OFF:
ON: Active / OFF: Hardwire Bypass
LF EQ Boost/Cut:
± 5 dB
HF EQ Boost/Cut:
± 5 dB
XOVER 1 Frequency:
100 Hz / 210 Hz
XOVER 2 Frequency:
1.7 kHz / 3.4 kHz
RELEASE Time:
150 mSec to 7 Sec
RCH (Relative Crest Height) DENSITY: STEREO COUPLING:
-5 to +5
STEREO COUPLING:
ON/OFF
PEAK CEILING:
+1 to +25dBu (PK)**
Peak Ceiling is adjusted with the COARSE (2dB steps), FINE (0.2dB steps) and RANGE (0dB/-10dB) controls
LIMITING Meter:
10 segment meter indicates up to 15dB of gain reduction in the channel with the greatest amount of limiting.
600 OHM INPUT TERMINATION:
Each channel is switchable on rear panel (lifts in bypass)
REMOTE Control Jack:
A four pin RJ11 telephone-style connector on the rear panel provides remote control capacity of the PROCESS ON/OFF bypass relays and dry “tally” contact for a remote status indicator
OTHER SPECIFICATIONS:
Power Input:
IEC standard receptacle with voltage selector, fuse and filter
Power Requirements:
100, 120, 220, or 240 VAC; 50 or 60 Hz
Power Consumption:
30 watts maximum
Power Fuse:
Slow blowing type- 100/120 VAC: 0.375 A; 220/240 VAC: 0.25A
Net Weight:
6 lbs. (2.72 kg)
Dimensions:
19” W x 1.75” H x 9.63” D (482.6 mm x 44.5 mm x 244.6 mm)
OTHER SPECIFICATIONS:
Power Input:
IEC standard receptacle with voltage selector, fuse and filter
Power Requirements:
100, 120, 220, or 240 VAC; 50 or 60 Hz
Power Consumption:
30 watts maximum
Power Fuse:
Slow blowing type- 100/120 VAC: 0.375 A; 220/240 VAC: 0.25A
Net Weight:
6 lbs. (2.72 kg)
Dimensions:
19” W x 1.75” H x 9.63” D (482.6 mm x 44.5 mm x 244.6 mm)
Locatie | Dordrecht |
Verhuurder | Rick Bakker Productions |
Afstand | |
Aantal beschikbaar | 2 stuk(s) |
Prijs p/d | € 12,50 |
In winkelwagen |