Rent Around

Two-way, constant curvature line array module
Compact and light; a “one-person lift”
Easy to mount, fly or ground stack
Two-module, pole-mounted arrays or up to five modules flown
Classic EAW output, pattern control and fidelity

Subsystem:

Transducer: LF – 2x 10 in. cone; HF – 3x.75 in. exit, 1.75 in voice coil compression driver
Loading: LF – Vented; HF – Horn-loaded

Operating Mode:

Amplifier Channels: Single-amp LF/LF; Bi-amp LF,HF
External Signal Processing: High pass filter; DSP w/2-way filter

Operating Range (-10 dB, Hz)

65 – 20k

Axial Sensitivity (1W @ 1m, dB SPL)

LF: 96
HF: 102
Full Range: 95

Power Handling / Impedance (Watts @ Ohms)

LF: 800 @ 8
HF: 80 @ 16
Full Range: 800 @ 8

Calculated Maximum Output Peak (dB SPL)

LF: 131
HF: 130
Full Range: 130

Calculated Maximum Output Long Term (dB SPL)

LF: 125
HF: 124
Full Range: 124

Nominal Coverage (degrees)

Horizontal: 110
Vertical: 15

Subsystems

LF: 2x 10-in cone, vented
HF: 3x .75-in exit compression driver, horn-loaded

Powering

Switchable: bi-amplified/passive

Dimensions (inches/millimeters)

Height: 12.37/314
Width: 24.84/631
Depth: 15.64/397

Trap. Angle (degrees top and bottom): 7.5

Weights (pounds/kilograms)

Net: 62/28
Shipping: 75/34

The JFL213 compact, two-way line array module features a range of EAW’s most innovative line array technologies within a mobile, light-weight package appropriate in a wide range of small- to medium-sized venues. With its companion subwoofer, the JFL118, this easy-to-use system solves problems in both portable and permanently installed applications.

The JFL213’s two-way design mounts dual 10-in cone transducers in an optimally vented enclosure and spaced to extend pattern control into the low frequency range. Three horn-loaded, 0.75-in exit / 1.75-in voice coil compression drivers deliver even dispersion of high frequency information over the entire 110° horizontal coverage area.

EAW engineers optimized the JFL213’s size, shape and weight for easy transport and setup by a single person, with side handles designed as part of the rigging system and aligned with the enclosure’s center of balance. Users can mount up to two JFL213s on a loudspeaker stand with a 35mm/1.38-in diameter pole. The cleverly-designed, dual-angle pole mount cup allows the bottom enclosure to be aimed 0° or -15°. (A two-module array with the lower modules aimed at -15° aims the upper module at 0°.) The JFL118 features an integrated pole mount cup, letting it serve as a large, stable base for pole mounting.

The JFL213’s ultra-strong rigging system allows users to hang up to five modules with a 10:1 safety factor, which meets or exceeds all standards enforced throughout the world. A single person can easily connect the modules to the accessory FB221 Fly Bar as well as to each other. The FB221 also doubles as
a ground stack base for up to four JFL213s. For permanent installation, each JFL213 provides a pair of M10 threaded mounting points.

The JFL213 allows users to switch between single- or bi-amp powering modes. The JFL213 delivers optimal performance when operated in bi-amp mode with an EAW UX Series digital processor. In addition to the HF shading filters, UX Series digital processor deliver EAW Focusing™ setting, which correct for anomalies that occur in the time domain of any loudspeaker or transducer.

Enclosures are protected by our tough, scratch-resistant RoadCoat™ finish and durable, foam-backed steel grilles protect the transducers. Six year warranty.

Locatie	Medemblik
Verhuurder	P-S-L Licht en geluid techniek
Afstand
Aantal beschikbaar	8 stuk(s)
Prijs p/d	€ 45,00
	In winkelwagen

EAW JFL213