Power Requirements: DC 12 V ±10 b (AC adapter provided)
Current Consumption: 2.0 A (DC 12 V)
Ambient Operating Temperature: 0 °C to 40 °C (32 °F to 104 °F)
Humidity: 10 to 90 % (no condensation)
Dimensions: (W x H x D) 210 x 67 x 177 mm
Mass: 1.4 kg (3.08 lbs.)
Video Terminal
Inputs 5 video lines
SDI: 4 signal lines: SDI IN 1 to SDI IN 4
DVI-D: 1 signal line: DVI IN
Outputs 3 video lines, 4 outputs
SDI 2 signal lines: SDI OUT 1, SDI OUT 2
(Only the SDI OUT 1 signals are split into two)
DVI-D 1 signal line: DVI OUT
Signal Formats
SD: 480/59.94i, 576/50i
HD 1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 1080/24PsF, 1080/23.98PsF
Signal Processing
Y:Cb:Cr 4:2:2, 10 bit (8 bits for frame memory)
RGB 4:4:4, 8 bit
ME Number: 1ME
SDI Inputs
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
4 signal lines: SDI IN 1 to SDI IN 4 SDI Inputs
HD: SMPTE 292M (BTA S-004B) standard complied with
0.8 V [p-p] ±10 ok (75Ω)
Input return loss More than 15 dB (5 MHz to 1.5 GHz)
Automatic equalizer 100 m (328 ft.) (when 5C-FB cable is used)
SD: SMPTE 259M standard complied with
0.8 V [p-p] ±10 0k (75Ω)
Input return loss More than 15 dB (5 MHz to 270 MHz)
Automatic equalizer 200 m (656 ft.) (when 5C-2V cable is used)
DVI-D Input
Digital ROB (Vertical frequency: 60 Hz): XGA (1024 x 768), WXGA (1280 x 768), SXGA (1280 x 1024), WSXGA+ (1680 x 1050), UXGA (1600 x 1200), WUXGA (1920 x 1200)
Digital RGB: 1080/50p, 1080/59.94p
Analog input signals are not supported. SDI Outputs
SDI Outputs
HD: Serial digital component (SMPTE 292M)
SD: Serial digital component (SMPTE 259M)
2 signal lines: SDI OUT 1, SDI OUT 2 (Only the SDI OUT 1 signals are split into two)
HD: SMPTE 292M (BTA S-004B) standard complied with
Output return loss More than 15dB (5 MHz to 1.5 GHz)
Output level 0.8 V [p-p] ±10 0/0 (75Ω)
Rise time Less than 270 ps
Fall time Less than 270 ps
Difference between rise time and fall time: Less than 100 ps
Alignment jitter: Less than 0.2 UI (130 ps)
Timing jitter Less than 1.0 UI
Eye aperture ratio More than 90%
DC offset 0±0.5 V
SD: SMPTE 259M standard complied with
Output return loss: More than 15 dB (5 MHz to 270 MHz)
Output level: 0.8 V [p-p] ±10% (75 Ω)
Rise time: Less than 1.5 ns
Fall time: Less than 1.5 ns
Difference between rise time and fall time: Less than 0.5 ns
Jitter: Less than 0.2 UI
DVI-D Output
Digital RGB (Vertical frequency: 60 Hz): XGA (1024 x 768), WXGA (1280 x 768), SXGA (1280 x 1024), WSXGA+ (1680 x 1050), UXGA (1600 x 1200), WUXGA (1920 x 1200) Digital RGB: 1080/50p, 1080/59.94p
High-resolution multi view mode supported: Signals are also output with a high resolution even when SD has been selected as the system mode.
When the high-resolution multi view mode is enabled, MV is assigned to the DVI OUT connector, and MV cannot be assigned to the SDI OUT 1 connectors or SDI OUT 2 connector.
Analog output signals are not supported.
Synchronous Terminal
Video Delay Time
1 frame (F)
Video signals that have passed through the PinP, multi view display, DVI-D input or DVI-D output will be delayed in each case by up to one frame.
Control Terminal
LAN
RJ-45 x 1 10BASE-T/100BASE-TA (For IP control) Connecting cable: IAN cable (category 5 or above), max. 100 m (328 ft.),
STP (Shielded Twisted Pair) cable recommended
When connecting to a hub (switching hub), use a straight cable. Use a crossover cable when connecting the unit and another device on a 1:1 basis without going through a hub.
TALLY/DPI
D-sub 15-pin, female, inch thread
INPUT: 5 inputs, photocoupler sensing
OUTPUT: 7 outputs, open collector output (negative logic)