Features
Power supply
- Powersoft legendary universal switch mode power supply up to 400VAC tolerant with Power Factor Correction
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
- Fully protected circuit design with:
-
- Ac protection: shut down power supply when AC mains voltage is outside operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long-term limiter: protects the loudspeaker against steady long-term rms (non-audio) signals reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high-grade sound accuracy
- Compact size - all models only 1 RU for reduced rack cost and space
- Lightweight - for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Settings
- Built-in defeatable clip limiters for each channel
- Digital gain-attenuator control
- Defeatable gate selection for each channel
- User selectable gain/sensitivity
- User selectable maximum output power for each channel
- User selectable maximum mains current draw
- Lockable set-up with user selectable access key code
- Built-in remote control via the RS-485 interface provides full diagnostic, operational setting, and system monitoring
Monitoring
- Hardware monitor available for fast local diagnostic
- Load impedance measurement for each channel
- Output power measurements for each channel
- Mains voltage and current measurements
- Downloadable log file of functional fault events with time-related trace
Remote management
- Control and monitoring through ArmoníaPlus
- Dedicated Web App
Remote Control & Monitoring
- Via Software:
- Attenuation (from 0 dB to 26 dB)
- Max output voltage
- Output and gain reduction metering
- Diagnostics (temperature, fans, …)
- Via Hardware:
- Attenuation (from 0 dB to 26 dB)
- High Pass Filter (35 Hz, 70 Hz)
- LoZ/HiZ/70V/100V output selection
- Gain (from 26 dB to 35 dB)
Specifications
General
- Number of channels: 4
- Output power
- Single channel mode
- 2Ω: 1500W
- 4Ω: 1200W
- 8Ω: 1200W
- Distributed line*
- Bridge mode
Max output voltage / current
: 140 Vpeak / 45 Apeak
AC Main Power
- Power supply: Universal, regulated switch mode with PFC (Power Factor Correction)
- Nominal power requirement: 100-240 V ±10%, 50-60 Hz
- Operating voltage: 90V - 264V
- Power consuption (230V)
- Idle: 32.4 W 0.33 A
- 1/8 of max output power@4Ω: 826.8W 5.02A
- 1/4 of max output power@4Ω: 1651W 9.41A
Audio
- Frequency response: 20 Hz - 20 kHz (±0.5 dB) @ 1 W, 8 Ω
- S/N ratio: > 110 dB (20 Hz - 20 kHz, A weighted)
- Crosstalk separation: > 70 dB @ 1kHz
- THD+N: 0.2% from 0.1 W to full power (typically < 0.05%)
- IMD: < 0.1% from 0.1 W to full power (typically < 0.05%)
- Input impedance: 20 kΩ balanced
- Slew rate: > 50 V/μs @ 8Ω, input filter bypassed
- Damping factor: > 500 @ 20-100 Hz
DSP
- AD Converter: 24 Bit Tandem™ @ 48 kHz 125 dB-A Dynamic Range - 0.005 % THD+N
- DA Converter: 24 Bit Tandem™ @ 48 kHz 117 dB-A Dynamic Range - 0.003 % THD+N
- Internal precision: 32 bit floating point
- Memory/presets: 128 MB (RAM) plus 512 MB fash for presets /
- Latency: 2.5 ms fixed latency architecture
- Input equalizer: Raised-cosine, custom FiR, parametric iiR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass
- Crossover: linear phase (FIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)
- Delay: 2 s (input) + 100 ms (output) for time alignment
- Input EQ
- Output EQ
- Limiters: TruePower™, RMS voltage, RMS current, Peak limiter
- Damping control: Active DampingControl™ and Liveimpedance™ measurement
Front panel (Connectors)
- AC main: 1 x IEC C20 connector - 20 A max (region-specific power cord provided)
- Audio signal input: 1 x 12 pin Phoenix MC 1.5/12-ST-3.81 - Signal input – MAIN
- Alarm
- 1 x 12 pin Phoenix MC 1.5/12-ST-3.81 - Alarm connector
- 1 x 4 pin Phoenix MC 1.5/4-ST-3.81 - Alarm connector
- Network/data
- 1 x Rj45 socket - RS485 data connection (non-DSP version)
- 1 x Rj45 socket - DANTE®
Construction
- Dimensions (L x H x W): 483 mm x 44.45 mm x 360 mm (19.0 in x 1.8 in x 14.2 in)
- Weight: 7 kg (15.4 lb)